Boat Trailer Wheel Clamp
Australian made since 2007.
...fits all size wheels...
Published by
on
how to stop thieves stealing your
Cruise Craft Boat Trailer
This week's article describes how to fit the Australian made Boat Trailer Wheel Clamp to one of the wheels on a Cruise Craft Boat Trailer.
Cruise Craft Boat Trailer
protected with
Boat Trailer Wheel Clamp
security option Supreme
also known as Australian Wheel Clamp.
Cruise Craft Boat Trailer
secured with
Australian Wheel Clamp
security option Supreme.
Australian Wheel Clamp
security option Supreme.
Australian Manufacturer Direct Special Offer
Tuesday April 24, 2018 between 10.30am to 9.30pm
Scroll down this page to read how much you will save.
Note: The Australian made Wheel Clamp has many names depending what it is being sold to secure eg. Australian Wheel Clamp, Caravan Wheel Clamp, Camper Trailer Wheel Clamp, Boat Trailer Wheel Clamp, Trailer Wheel Clamp and others.
Included in this page...
There are two methods to fit the Australian made Wheel Clamp depending on the Vehicle type. The following list is a guide to indicate whether you use fitting method one or two.
Fitting Method One
Fitting Method One
Fitting Method Two
Choose the correct fitting method from the above list of vehicles then download the instructions, in PDF format, from the following list.
Australian Wheel Clamp
security option Supreme.
Security Rating
Ultimate Protection
STOPS all methods thieves use to cut Chain or break a Padlock. This represents over
99% of all thieves.
...plus...
it is QUICK and simple to fit to and remove from a Wheel.
the world's
Highest Security Rated
Australian made Wheel Clamp
Cruise Craft Boat Trailer
secured with
Australian Wheel Clamp
security option Supreme.
Fitting method one is used to secure vehicles that have enough space between the top of the Wheel and the bottom of the Wheel Arch. This allows you to put your hand between to place the 10mm diameter High Tensile Chain under then over the top of the leaf springs or tubular frame as seen in the following pictures.
Australian Wheel Clamp
security option Supreme.
High Tensile Chain
wrapped round leaf springs.
Fitting method two is used when you cannot get your hand between the Wheel Arch and the top of the Wheel, see Vehicle list in number one above.
This Web Site explains why the Australian made Wheel Clamp is completely different compared to all other wheel clamps and has a unique method to fit it to a Wheel and the vehicle's chassis.
Practically all wheel clamps are made one of three ways...
Plus some type of lock at the front or side, as per the following pictures.
Klamp IT
Haigh Wheel Clamp
Ark Wheel Clamp
Whereas the Australian made Wheel Clamp incorporates a length of 10mm diameter High Tensile Chain.
The method used to secure the 10mm diameter High Tensile Chain to the Wheel through the Stainless Steel Shield at 4 points and round the towable or driveable vehicle's leaf springs or tubular frame at 2 points or another part of the chassis if the Vehicle has coil springs and/or piston suspension.
Then locks at the front:
High Tensile Chain
wrapped round leaf springs.
Back of Wheel
High Tensile Chain wrapped round leaf springs and Wheel.
Stainless Steel Shield
with High Tensile Chain.
Australian Wheel Clamp
security option Enforcer.
Australian Wheel Clamp
security option Supreme.
...plus...
both security options are
QUICK and simple to fit to and remove from a Wheel.
Cruise Craft Boat Trailer
secured with
Australian Wheel Clamp
security option Supreme.
Step 1
Stand the Steel Shield in front of the Wheel.
Step 2
Place the Chain through the two bottom holes in the Steel Shield.
NB: Step 2 - We suggest to save you a few seconds while fitting the Australian Wheel Clamp security option Supreme place a piece of coloured tape or twist a short piece of wire, as seen in the pictures, or similar around the middle link in the length of Chain. This will enable you to quickly centralize the Chain in the center of the Steel Shield.
Step 3
On the left side pass the Chain under then over the vehicle's leaf springs or tubular frame (as used to make most Caravan chassis) then through the top hole.
Step 4
Repeat the same procedure on the right side as per Step 3.
Back of Wheel
High Tensile Chain wrapped round leaf springs and Wheel.
Note...
If your towable or drivable Vehicle has coil springs and/or piston suspension, seen in the following picture, steps 1 and 2 are the same but as there are no leaf springs, seen in the pictures in steps 3 and 4 above, instead you wrap the Chain round any part of the chassis.
Steps 5 and 6 are the same no mater leaf springs or coil springs and/or piston suspension.
Kimberley Kamper back of the Wheel showing how the High Tensile Chain wraps round the chassis.
Step 5
Grip both ends of the Chain and pull to make the Chain taut.
Step 6
Locking the Australian Wheel Clamp security option Supreme with the patented Padlock Protection Steel Shroud and customised Padlock - opens in a new window, it will only take a few times to get the hang of it.
Steel Shroud, 10mm diameter High Tensile Chain and customised Padlock partially assembled.
10mm diameter High Tensile Chain cannot be cut with a Bolt Cutter no matter how long the Bolt Cutter is.
1st: Place both ends of the Chain in the slot on each side of the Steel Shroud.
2nd: Place the removable Shackle in the holes at the top of the Steel Shroud.
3rd: Hold the Steel Shroud in your hand and place a couple of fingers over the top of the Shackle. Look at the opposite end of the Steel Shroud to make sure the Shackle is in the center then insert the Padlock Body in the hole at the bottom of the Steel Shroud. To lock the Padlock turn the key after pushing the Padlock into the Shackle.
Note: The padlock's Shackle only fits into the Padlock body one way, you have to remember the correct way, here's a couple of suggestions:
Simple to fit to a Wheel.
Takes less than a minute to fit.
STOPS
all methods used to break a Padlock and cut Chain.
the world's
Highest Security Rated
Australian made Wheel Clamp
Australian Wheel Clamp
security option Supreme.
Security Rating
Ultimate Protection
STOPS all methods thieves use to cut Chain or break a Padlock. This represents over
99% of all thieves.
...plus...
it is QUICK and simple to fit to and remove from a Wheel.
Cruise Craft Boat Trailer
is now protected.
Cruise Craft Boat Trailer
secured with
Australian Wheel Clamp
security option Supreme.
I trust if you own or are thinking about purchasing a Cruise Craft Boat Trailer you seriously consider purchasing Boat Trailer Wheel Clamp, security option Supreme to stop it being stolen.
If you gained knowledge from reading this page
please email this page link to a friend, thank you.
Or...
Share this link
www.boat-trailer-wheel-clamp.com.au/articles-2016/cruise-craft-boats.php
on your favourite social network.
if you have a question or comment about the above article or if you want information about the Boat Trailer Wheel Clamp or any of the Theft Proof Security Products below please send us an email.
Australian Manufacturer Direct Special Offer
Tuesday April 24, 2018 between 10.30am to 9.30pm
save $170 or $188
Plus next business day free delivery anywhere in Australia.
Read our offer Now...
Theft Proof Security Products Web Sites
Below links open in a new window.
High Security, Light-Weight
Virtually Indestructible Safe
Easy DIY Installation in:
Residential Homes, Vehicles
Caravans, Motor Homes, RV’s, Offices, Factories and Boats.
If you don't need any more information to make a decision to purchase.
Site Map